admin58 – CJ ROMBOLD

September 3, 2026 0

Camaro Maintenance

We rebuilt the engine for this Camaro a few years back. The car is in for a check up.

admin58

October 2, 2025 0

We built a 565 CI for this car and it was in for Dyno tuning after being installed. With a F2R ProCharger at 6-8 lbs of boost with a street tune we were making 864 HP and 718 TQ. We tried to video with a semi pro recorder with a pro mic and at 20…

admin58

May 31, 2025 0

455 Olds

This 455 Oldsmobile came in for a rebuild. The stock block bottom end has been reinforced for the blower. Parts include a Hampton Blower System, 750 Quick Fuel Carburetors, Edelbrock RPM Performer Intake, MSD Distributor & Coil, and Mallory Plug Wires. This Olds made over 740 HP & 760 TQ.

admin58

January 23, 2025 0

496 Big Block Chevrolet

Starting off 2025 with this 496 ci Big Block with 10.5 to 1 compression. This BBC made 612 HP & 580 TQ. Parts include LPC Forged Rotating Assembly, Hydraulic Roller Cam, LPC Aluminum Heads, and a Holley 850 Carburetor.

admin58

August 15, 2024 0

Old School 327 Chevrolet

This 327 was from 1962 or 1963 and in 1970 was rebuilt and never started and put away. When purchased in 2024 it came with all the receipts from the build. For example the previous owner bought a brand new set of 302 DZ Heads casting #186 complete for $149.00 back in 1970. We did…

admin58

May 10, 2024 0

540 Big Block Chevrolet

Tuesday night Dyno pulls with a 540 CI BB Chevy. Bits and pieces include Dart Block, Forged Rotating Assembly, Comp Solid Roller Cam, Liberty Heads with 340 cc intake runners, Edelbrock Super Victor Intake, topped off with a Holley 1050 XP Dominator. After break in made 796 HP & 712 TQ.

admin58

March 9, 2024 0

445 Ford Stroker

This 445 CI Ford started as a 390. Parts include Scatt Rotating Assembly, Crower Hydraulic Roller Cam, Edelbrock Performer RPM Heads, Edelbrock Performer RPM Intake, and a 750 Brawler Carburetor. This combination made 501 HP & 564 TQ on pump gas. Check out our Facebook page for the video. As always Thank you for your…

admin58

January 19, 2024 0

408 LS Stroker

This LS was built for a customer that we have built several engines for. This particular LS was assembled for boost with 9:1 compression. We started out with a Scatt crankshaft, Oliver Racing Parts connecting rods, and Diamond pistons. Then we added a Brian Tooley Racing camshaft and Dart Pro 1 cylinder heads. We Dyno…

admin58

November 18, 2023 0

351 Cleveland

This Ford 351 has a stock rotating assembly, hydraulic roller cam, Trick Flow heads, Edelbrock RPM Air Gap manifold, and a Summit 750 carburetor. This Cleveland made 454 HP & 453 TQ on the Engine Dyno with pump gas.

admin58

September 24, 2023 0

427 CI Blower Engine

This little number is being installed into a Hot Rod Coupe and made 680 HP & 650 TQ @ 6 lbs of boost on pump gas. Parts include a Dart Block, Scat Rotating Assembly, Erson Roller Cam, Liberty Heads, Weiand 671 Blower, And two Brawler 650 Carbs. See the video on our Facebook page!

admin58